Fehlermeldung

  • Deprecated function: The each() function is deprecated. This message will be suppressed on further calls in _menu_load_objects() (Zeile 579 von /is/htdocs/wp1126794_5XJ8L03NJV/pbadcon/includes/menu.inc).
  • Deprecated function: implode(): Passing glue string after array is deprecated. Swap the parameters in drupal_get_feeds() (Zeile 394 von /is/htdocs/wp1126794_5XJ8L03NJV/pbadcon/includes/common.inc).

fluke networks ms2-100 manual

fluke networks ms2-100 manual

LINK 1 ENTER SITE >>> http://gg.gg/11mut9 <<< Download
LINK 2 ENTER SITE >>> http://inx.lv/2xJB <<< Download PDF

File Name:fluke networks ms2-100 manual.pdf
Size: 4844 KB
Type: PDF, ePub, eBook
Uploaded: 5 May 2019, 19:19
Rating: 4.6/5 from 769 votes.
Status: AVAILABLE
Last checked: 8 Minutes ago!
eBook includes PDF, ePub and Kindle version
In order to read or download fluke networks ms2-100 manual ebook, you need to create a FREE account.

✔ Register a free 1 month Trial Account.
✔ Download as many books as you like (Personal use)
✔ Cancel the membership at any time if not satisfied.
✔ Join Over 80000 Happy Readers
fluke networks ms2-100 manual

Fluke Networks does not warrant that software will be error free or operate without interruption. This equipment is intended for Fluke Networks.Disconnect the tester if cause burns or explode. If exposure to chemicals appear. Figures 1 and 11 show examples of this occurs, clean with water and get medical aid. Without this termination, the tester cannot detect crossed wires or crossed pairs. Open on Twisted Pair Cabling Figure 6 shows an open on wire 4. Notes If only one wire in a pair is open and a wiremap adapter or remote ID locator is not connected, both wires are shown as open. The the pin wires flash to indicate the fault. The cable length is 75.4 m. numbers flash to indicate the fault. The pin numbers flash to indicate the fault. This crossed pair is likely caused by mixing 568A and 568B cabling. Detection of crossed pairs requires a far-end adapter. egk09.eps Figure 9. The cable length is 75.4 m. In a split pair, continuity from end to end is correct, but is made with wires from different pairs. The distance to a bridge tap is approximate because multiple reflections from the bridge tap interfere with length measurements. Note Bridge taps more than 328 ft (100 m) from the tester or taps less than 16 ft (5 m) long may not be. Dashes are shown if the tester cannot Ethernet Port Detected measure the length. This can occur if the port does not The tester can detect active and inactive Ethernet ports, as produce reflections.On the individual results screens, shorts are shown only when they are between wires in a pair. Telephone cables wired in a star topology (Figure 16) are connected together at a bridge tap at the distribution If you connect the tester to the bridge tap, the tester center. See “Connecting to Star Topologies” for details. egk16.eps Figure 16. For cabling not terminated with an F-connector, use an adapter or hybrid patch cord to connect to the cabling. Connect the tester to the cable.Use the tester to check for shorts.
http://www.karthikeyanjayaram.in/userfiles/final-fantasy-vii-pc-manual.xml

fluke networks ms2-100 manual, fluke networks ms2-100, fluke networks ms2-100 cable tester manual, fluke networks ms2-100 manual, fluke networks ms2-100 manual user, fluke networks ms2-100 manual pdf, fluke networks ms2-100 manual instructions, fluke networks ms2-100 manual transmission.

Use the probe to isolate the tone source in the cable bundle or at the patch panel. This function changes the toner’s song The tester’s IntelliTone function works with an optional when you short a wire pair in the cable connected to the IP200 probe’s cable map function to verify wiring at the far tester. You may change the LED’s function to indicate shield continuity. See the probe’s documentation for details. LEDs show the wiremap. Test connectors F-connector for coaxial cable. Battery type: 2 AA (NEDA 15A, IEC LR6) alkaline batteries Power Battery life: 20 hours of typical use Other compatible battery types: 2 AA photo lithium, NIMH, NICAD 3 in x 6.4”. It has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15, Subpart J of the FCC rules, which are designed to provide reasonable protection against such interference. It starts by taking results from what was four different test modes and displaying them all at once - graphical wiremap, pair lengths, distance to fault, cable ID, and far end device. What's more, its integrated RJ11, RJ45, and coax test ports support virtually any type of low-voltage cable testing with no need for awkward adapters. The end result is reduced test time and technician error. That makes high-quality installations more efficient and troubleshooting easier. MicroScanner 2: F-connector for coaxial cable. Power Battery type: 2 AA (NEDA 15A, IEC LR6) alkaline batteries Battery life: 20 hours of typical use Other compatible battery types: 2 AA photo lithium, NIMH, NICAD Dimensions and weight (with batteries installed and wiremap adapter attached) 3 in x 6.4in x 1.4 in (7.6 cm x 16.3 cm x 3.6 cm) MicroScanner 2: 10.6 oz (300 g) Display Monochrome LCD with backlight Test modes Cable test Measures length, verifies wiremap, identifies remote ID locators, and detects Ethernet ports. MicroScanner PoE also shows HIGH.NVP uncertainty is an additional error.
http://giaynangchieucao.com/userfiles/final-fantasy-vi-manual.xml

Calibration: User-settable NVP for twisted pair and coax (MicroScanner 2 ). Can determine actual NVP with known length of cable. Wiremap test Detects single-wire faults, shorts, miswires, split pairs, and up to seven far-end adapter IDs. The wiremap is drawn with proportional length to visually indicate the approximate location of faults. Ethernet port detection MicroScanner 2: Detects the advertised speed of 802.3 Ethernet ports with speeds of 10 Mbps, 100 Mbps, and 1 Gbps. Generates four tones compatible with typical analog probes. All rights reserved. All product names are trademarks of their respective companies. The warranty period for the mainframe is one year and begins on the date of purchase. Parts, accessories, product repairs and services are warranted for 90 days, unless otherwise stated. Ni-Cad, Ni-MH and Li-Ion batteries, cables or other peripherals are all considered parts or accessories. The warranty extends only to the original buyer or end user customer of a Fluke Networks authorized reseller, and does not apply to any product which, in Fluke Networks opinion, has been misused, abused, altered, neglected, contaminated, or damaged by accident or abnormal conditions of operation or handling. Fluke Networks warrants that software will operate substantially in accordance with its functional specifications for 90 days and that it has been properly recorded on non-defective media. Fluke Networks does not warrant that software will be error free or operate without interruption. Fluke Networks authorized resellers shall extend this warranty on new and unused products to end-user customers only but have no authority to extend a greater or different warranty on behalf of Fluke Networks. Warranty support is available only if product is purchased through a Fluke Networks authorized sales outlet or Buyer has paid the applicable international price.
https://labroclub.ru/blog/e1005-service-manual

Fluke Networks warranty obligation is limited, at Fluke Networks option, to refund of the purchase price, free of charge repair, or replacement of a defective product which is returned to a Fluke Networks authorized service center within the warranty period. To obtain warranty service, contact your nearest Fluke Networks authorized service center to obtain return authorization information, then send the product to that service center, with a description of the difficulty, postage and insurance prepaid (FOB destination). Fluke Networks assumes no risk for damage in transit. Following warranty repair, the product will be returned to Buyer, transportation prepaid (FOB destination). If Fluke Networks determines that failure was caused by neglect, misuse, contamination, alteration, accident or abnormal condition of operation or handling, or normal wear and tear of mechanical components, Fluke Networks will provide an estimate of repair costs and obtain authorization before commencing the work. Following repair, the product will be returned to the Buyer transportation prepaid and the Buyer will be billed for the repair and return transportation charges (FOB Shipping point).The tester does the following: Measures length up to 1500 ft (457 m) and detects opens and shorts on twisted pair and coaxial cabling. Detects split pairs on twisted pair cabling. Displays wiremap, cable length, proportional distance to opens, and the remote ID number all on one screen. Detects Ethernet ports on twisted pair cabling and reports the port speed. Detects PoE (Power over Ethernet) and telephone voltages on twisted pair cabling. IntelliTone function works with an optional Fluke Networks IntelliTone probe to help you locate and isolate cables behind walls, at patch panels, or in bundles. The analog toner works with standard analog probes and includes the SmartTone function for positive identification of cables in bundles.

1 If something is damaged or missing, contact the place of purchase immediately.See explanations in the manual. On the tester s display this symbol indicates a cable fault or voltage on the cable. X Warning: Risk of electric shock. WWarningX To avoid possible fire, electric shock, or personal injury: Do not open the case; no user-serviceable parts are inside. Do not modify the tester. Do not use the tester if it is damaged. Inspect the tester before use. If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. Dispose of circuits boards in accordance with local regulations. The tester is not intended to be connected to active telephone inputs, systems, or equipment, including ISDN devices. Prolonged exposure to the voltages applied by these interfaces may damage the tester. The tester shows a warning symbol (W) and the voltage polarities when it detects high voltage. Figures 1 and 11 show examples of this display. 4 Do not use the tester if it operates abnormally. Protection may be impaired. Positive Negative Figure 1. High Voltage Display Example egk29.eps 5 B E, D: Navigates through screens and changes settings. In toner mode, these keys cycle through the IntelliTone and analog toner songs. C Y: Selects the RJ45 or coaxial connector as the active port. D M: Cycles through the cable test, toner, and PoE detect modes. Note Auto shutoff is disabled in demonstration mode. E LCD display with backlight. G H I Modular jack for connecting to telephone and twisted pair network cable. The jack accepts 8-pin modular (RJ45) and 6-pin modular (RJ11) connectors. Wiremap adapter with F-connector and 8-pin modular jack. See page 10. Optional remote ID locator with F-connector and 8-pin modular jack. See page 10. 7 See page 20. C Indicates which port is active, the RJ45 port (U) or the coaxial port (T). D Tone mode indicator. See page 32. E Power over Ethernet mode indicator.

G Test activity indicator, which is animated when a test is running. H IntelliTone appears when the toner is in IntelliTone mode. See pages 32 and 36. I Indicates a short on the cable. See pages 13 and 30. J Telephone voltage indicator. See page 16. K Indicates a wiremap adapter is connected to the far end of the cable. L Low battery indicator. See page 40. M Indicates an ID locator is connected to the far end of the cable and shows the locator s number. N Ethernet port indicator. See page 18. 8 For opens, the number of segments lit for the wire pair indicates the approximate distance to the fault. The rightmost segments indicate the shield. See pages 12 through 15. The W Indicates a fault or high voltage on the cable. SPLIT appears when the fault is a split pair. See page 15. Auto Shutoff Changing the Length Units 1 Hold down Y and E while turning on the tester. 2 Press M to switch between meters and feet. 3 Turn the tester off then on to return to testing mode. Auto Shutoff The tester turns off after 10 minutes if no keys are pressed and nothing changes at the tester s connectors. Note Auto shutoff is disabled in toner and demonstration modes. 9 Without this termination, the tester cannot detect crossed wires or crossed pairs. For a wire pair with one wire open, termination is required to detect which wire is open. Without termination, the tester shows both wires as open. Using multiple remote ID locators helps you identify connections at patch panels. The tester shows the number of the locator connected to the far end of the cabling, as shown on page 23. To connect a remote ID locator to a modular (RJ) jack in a confined area or to a 4-pin modular jack (RJ11), use the optional universal adapter and a patch cord, as shown in Figure 4. Remote ID locator Universal adapter (8-pin and 4-pin) 8-pin or 4-pin modular patch cord egk15.eps Figure 4.

Connecting a Remote ID Locator in a Confined Area or to an RJ11 Jack 10 If the tester is already on and in coaxial test mode (T), press Y to switch to twisted pair test mode (U). 2 Connect the tester and wiremap adapter or ID locator to the cabling as shown in Figures 5 through 17. The test runs continuously until you change modes or turn the tester off. Notes You can measure length without connecting a far end adapter; however, an adapter is required for a complete wiremap test. If the PoE indicator appears, see page 31. Patch panel RJ45 patch cords Wiremap adapter Wall outlet egk03.eps Figure 5. Connecting to Twisted Pair Network Cabling 11 Open on Twisted Pair Cabling Figure 6 shows an open on wire 4. Notes If only one wire in a pair is open and a wiremap adapter or remote ID locator is not connected, both wires are shown as open. The warning icon (W) does not appear if both wires in a pair are open because open pairs are normal for some cabling applications. The cable length is 75.4 m. To see the distance to the open, use E or D to view the individual result for the wire pair. See page 20. Figure 6. Open on Twisted Pair Cabling egk05.eps 12 The cable length is 75.4 m. Note When there is a short, the far-end adapter and the mapping of the unshorted wires are not shown. Crossed Wires Figure 8 shows that wires 3 and 4 are crossed. The the pin numbers flash to indicate the fault. Cable length is 53.9 m. The cable is shielded. Detection of crossed wires requires a far-end adapter. Short icon Shield indicator Figure 7. Short on Twisted Pair Cabling ekg06.eps Figure 8. Crossed Wires egk08.eps 13 22 MicroScanner 2 Cable Verifier Users Manual Crossed Pairs Figure 9 shows that pairs 1,2 and 3,6 are crossed. The pin numbers flash to indicate the fault. This crossed pair is likely caused by mixing 568A and 568B cabling. Detection of crossed pairs requires a far-end adapter. Figure 9. Crossed Pairs egk09.

eps 14 23 Testing Twisted Pair Cabling Split Pair Figure 10 shows a split pair on 3,6 and 4,5. The split pair flashes to indicate the fault. The cable length is 75.4 m. In a split pair, continuity from end to end is correct, but is made with wires from different pairs. Split pairs cause excessive crosstalk that interferes with network operation. Note Cables with untwisted pairs, such as telephone cords, typically show split pairs due to excessive crosstalk. Split pair icon The split pair flashes Split pair wiring Figure 10. Split Pair egk10.eps 15 24 MicroScanner 2 Cable Verifier Users Manual Telephone Voltages Detected Figure 11 shows that telephone voltage is detected on pair 4,5. Telephone voltage icon Length is not shown because the voltage interferes with length measurements. WWarningX The tester is not intended to be connected to active telephone inputs, systems, or equipment, including ISDN devices. Prolonged exposure to the voltages applied by these interfaces may damage the tester. Positive wire (tip) Negative wire (ring) Figure 11. Telephone Voltages Detected egk11.eps 16 25 Testing Twisted Pair Cabling Bridge Tap Detected Figure 12 shows a bridge tap detected at about 53.2 m. Only the first bridge tap detected is reported. The distance to a bridge tap is approximate because multiple reflections from the bridge tap interfere with length measurements. Note Bridge taps more than 328 ft (100 m) from the tester or taps less than 16 ft (5 m) long may not be detected. Figure 12. Bridge Tap Detected egk12.eps 17 26 MicroScanner 2 Cable Verifier Users Manual Ethernet Port Detected The tester can detect active and inactive Ethernet ports, as shown in Figure 13. A B Ethernet port icon. Port speed for an active 1000 megabit port. The speeds are 10, 100, or 1000 megabits per second. The example shows 1000 megabits per second. If the port supports multiple speeds the number cycles through the speeds. C Cable length.

Dashes are shown if the tester cannot measure the length. This can occur if the port does not produce reflections. Length may fluctuate or be obviously too high if the port s impedance fluctuates or varies from the cable s impedance. When in doubt, disconnect the cable from the port to get an accurate length measurement. 18 27 Testing Twisted Pair Cabling C C A A B Active Ethernet port Figure 13. Ethernet Port Detected Inactive Ethernet port egk13.eps 19 28 MicroScanner 2 Cable Verifier Users Manual Viewing Individual Results To see individual results for each wire pair, use E or D; to move among the screens. In this mode, the tester continuously tests only the wire pair you are viewing. Figure 14 shows examples of these screens. A Short on pair 1,2 at 29.8 m. Notes On the individual results screens, shorts are shown only when they are between wires in a pair. B C When there is a short, the far-end adapter and the mapping of the unshorted wires are not shown. Pair 3,6 is 67.7 m long and is terminated with the wiremap adapter. Open on pair 4,5 at 48.1 m. The open could be on one or both wires. 20 29 Testing Twisted Pair Cabling Figure 14. Results Screens for Individual Wire Pairs egk14.eps 21 30 MicroScanner 2 Cable Verifier Users Manual Using Multiple Remote ID Locators Using multiple remote ID locators helps you identify multiple network connections at a patch panel, as shown in Figure 15. WCaution Do not use multiple far end adapters in star or bus topologies. Doing so causes incorrect wiremap results. Using Multiple Remote ID Locators egk04.eps 23 32 MicroScanner 2 Cable Verifier Users Manual Connecting to Telephone Networks Wired in Star Topologies Telephone cables wired in a star topology (Figure 16) are connected together at a bridge tap at the distribution center. The bridge tap connects each wire to all other wires of the same number. The tester detects bridge taps and measures the distance to the bridge tap.

To measure the length of each cable connected to the bridge tap, connect the wiremap adapter or remote ID locator to the bridge tap and the tester to the wall outlet. The tester cannot measure length past the bridge tap because reflections from the bridge tap connections interfere with measurements. If you connect the tester to the bridge tap, the tester measures the length only to the bridge tap, which is only the patch cord length. WCaution Do not use multiple far end adapters in star or bus topologies. Doing so causes incorrect wiremap results. 24 33 Testing Twisted Pair Cabling Distribution center RJ11 patch cord Common connection to bridge tap RJ11 patch cord Wall outlets Wiremap adapter Note: For a correct length reading, connect the tester and wiremap adapter as shown. See Connecting to Star Topologies for details. Figure 16. Connecting to a Telephone Network Wired in a Star Topology egk16.eps 25 34 MicroScanner 2 Cable Verifier Users Manual Connecting to Telephone Networks Wired in Bus Topologies Telephone cables wired in a bus topology (Figure 17) connect the wall outlets in series. In this topology, you measure the length from the last outlet to the wiremap adapter. If you connect to an outlet in the middle of the series, the tester reports a bridge tap. The length reported is the length to the outlet, which is the patch cord length. The tester cannot measure length past the outlet because reflections from the cables on either side interfere with measurements. If you are unsure which outlet is the last in the bus, do the following: 1 Connect the wiremap adapter or ID locator to the beginning of the bus at the distribution center. 2 Connect the tester to an outlet and run the twisted pair cable test. If the tester reports a bridge tap, move to another outlet. The last outlet will not show a bridge tap, and will show the length to the distribution center. WCaution Do not use multiple far end adapters in star or bus topologies.

Doing so causes incorrect wiremap results. 26 35 Testing Twisted Pair Cabling Distribution center RJ11 patch cord Connection to bus Wall outlets Wiremap adapter RJ11 patch cord Note: Locations of the tester and wiremap adapter may be swapped. Figure 17. Connecting to a Telephone Network Wired in a Bus Topology egk17.eps 27 36 MicroScanner 2 Cable Verifier Users Manual Testing Coaxial Cabling 1 Turn on the tester; then press Y to switch to coaxial test mode (T). Connection to service 2 Connect the tester and wiremap adapter or ID locator to the cabling as shown in Figure 18. For cabling not terminated with an F-connector, use an adapter or hybrid patch cord to connect to the cabling. The test runs continuously until you change modes or turn the tester off. Coaxial patch cords Wall outlet Wiremap adapter Figure 18. Connecting to Coaxial Cabling egk19.eps 28 37 Testing Coaxial Cabling Coaxial Results Figure 19 shows a good coaxial cable 38.4 m long and terminated with remote ID number 3. Open on Coaxial Cabling Figure 20 shows an open 12.1 m from the tester. Figure 19. Coaxial Results egk20.eps Figure 20. Open on Coaxial Cabling egk21.eps 29 38 MicroScanner 2 Cable Verifier Users Manual Short on Coaxial Cabling Figure 21 shows a short 12.1 m from the tester. Unknown Termination on Coaxial Cabling Figure 22 shows a cable connected to a device at the far end, such as a television, CATV service, VCR, DVD player, satellite dish, splitter, or antenna. Dashes shown for length mean the tester cannot measure length because the device does not produce reflections. Figure 21. Short on Coaxial Cabling egk22.eps egk23.eps Figure 22. Unknown Termination on Coaxial Cabling 30 39 Detecting Power Over Ethernet Detecting Power Over Ethernet The tester can detect PoE voltage from 802.3af sources. To select PoE mode, press M until PoE appears on the display, as shown in Figure 23 (A). In PoE mode, the tester solicits PoE power on pairs 1,2-3,6 and 4,5-7,8.

The tester may activate a PoE source and will not be damaged by PoE power. If PoE power is detected, Poeappears above the powered pairs (B). The Poemay blink as the PoE source turns the power on and off. In twisted pair test mode, a flashing PoE mode indicator means that PoE power may be available. To verify the presence of a PoE source, switch the tester to PoE mode. Note The tester will not detect PoE schemes that are not compliant with the IEEE 802.3af standard, such as Cisco Inline Power. Figure 23. PoE Display egk30.eps 31 40 MicroScanner 2 Cable Verifier Users Manual Using the Toner You can use the tester with an optional tone probe to locate cables in bundles, at patch panels, or behind walls. Use the tester s IntelliTone mode with an optional Fluke Networks IP100 or IP200 tone probe. The digital IntelliTone signal is easier to detect at a distance than analog tones, and its frequency and encoding eliminate cable misidentification due to signal bleed and radiated or ambient noise. The tester s analog tone mode is compatible with most tone probes. The analog tone mode features the SmartTone function for positive identification of cables in bundles. Toning in IntelliTone Mode (optional IntelliTone probe required) Refer to Figures 24 and Connect the tester to the cable. 2 Press Y to select twisted pair (U) or coaxial (T) cable. 3 Press M until L, IntelliTone, and and a scrolling pattern of 1s and 0s appear on the display (A, B, and C in Figure 24). 4 To toggle between the two IntelliTone songs press E then D. The display shows the song number (D). If you press D or E repeatedly, the tester cycles through the IntelliTone and analog songs. 5 Turn the probe s rotary switch to M (locate). 6 Use the probe to find the general location of the tone at a cable rack, patch panel, or behind a wall, as shown in Figure 25. The SYNC LED lights up green when the probe is receiving the IntelliTone signal. The probe s LEDs light up from 1 to 8 as the signal strength increases.

The higher the number, the stronger the signal. 32 41 Using the Toner Notes If you cannot locate the IntelliTone signal on 2-conductor cables, the cable may be shorted. Use the tester to check for shorts. See pages 11 and Turn the probe s rotary switch to N (isolate). 8 Use the probe to isolate the tone source in the cable bundle or at the patch panel. The SYNC LED lights up green when the probe is receiving the IntelliTone signal. The probe s LEDs light up from 1 to 8 as the signal strength increases. The higher the number, the stronger the signal. Figure 24. IntelliTone Toner Mode Display egk07.eps 33 42 MicroScanner 2 Cable Verifier Users Manual Locating Cables Isolating Cables Wall outlet Volume control Figure 25. Using the Toner in IntelliTone Mode egk24.eps 34 43 Using the Toner Analog Toner Mode (optional tone probe required) Refer to Figure Connect the tester to the cable. 2 Press Y to select twisted pair or coaxial cable. 3 Press M until L appears on the display (A); then press D to enter analog toner mode. The display shows a scrolling sinewave in analog toner mode (B). 4 To change songs, press D. The display shows the song number (C). The analog toner has four songs. C A B If you press D or E repeatedly, the tester cycles through the analog and IntelliTone songs. 5 Use the probe to search for the cable. Figure 26. Analog Toner Mode Display egk25.eps 35 44 MicroScanner 2 Cable Verifier Users Manual Using the SmartTone Function Use the SmartTone function when you have trouble locating a cable. This function changes the toner s song when you short a wire pair in the cable connected to the tester. SmartTone works with the IntelliTone probe and with analog probes. Note Use the SmartTone function only on dry pairs of wires that are unterminated at both ends. Do not use this function on powered wires. 1 Press Y to select twisted pair or coaxial cabling. 2 Press M until L appears on the display.

3 Press D to select the analog toner mode (IntelliTone disappears from the display). 4 At the far end of the cabling, place the probe near the ends of the cables. 5 Momentarily short a wire pair in a cable (twisted pair) or short the conductor and shield in a cable (coaxial). If the song changes when you release the short, you have found the cable connected to the tester. Using the IntelliTone Cable Map Function (optional IP200 probe required) The tester s IntelliTone function works with an optional IP200 probe s cable map function to verify wiring at the far end of the cabling. The probe s cable map function identifies the most common wiring faults on twisted pair cabling: shorts, opens, and crossed pairs. 1 Press Y to select twisted pair cabling (U). 2 Turn the probe s rotary switch to CABLE MAP. 3 Connect the tester and probe to the cabling as shown in Figure Press M until L appears on the display. IntelliTone mode is indicated by IntelliTone and a scrolling pattern of 1s and 0s on the display. See Figure The probe s LEDs light in sequence to indicate the cable s wiring. See the probe s documentation for details. 36 View more All rights reserved. Printed in China. All product names are trademarks of their respective All product names are trademarks of their respective companies. i LIMITED All product names are trademarks of their respective companies.All rights reserved. All product names are trademarks of their respective companies.Specifications are subject to change without notice. All product names are trademarks of their respective Model: SPA8000 UserOs Manual Notice Every effort was made to ensure that the information in this guide was complete and accurate at the time of Printed in China. All product names are trademarks of their respective companies. LIMITED Previous experience of networking will be beneficial User s Manual and Installation Guide Copyright 1998 NetMedia Inc., All rights reserved. Rev. 061898 Thank you for your purchase of Caller-TV.

You are now ready to enjoy the convenience This test tool enables you to quickly check the network, test a cable, or PING. Users Manual Owner s Manual 1 Printed in USA All product names are trademarks of their Package contents Photo Frame AC Adapter Please read this user s guide before installing, setting up, and using your new weather It is for use on de-energised circuits only, however the Instrument This lets your cable modem provide Internet access to a computer or other device connected Making Your Mobile Life Easier. User Operation Manual.Designed and manufactured with pride in the UK. User Guide Operation is subject to the following two conditions: (1) This device may not cause User Manual These limits are designed to provide reasonable protection Please inform your local Axis office of any inaccuracies or omissions. Axis Communications User Guide FCC Radio Frequency Remote Control Extender OWNER S MANUAL During this period, this product User s Manual All rights reserved. No It tests installed cables or patch cords with RJ-45, RJ-11, 1394, USB and BNC connectors. It is intended to test cables with If you should ever have any questions or concerns about this product, feel free to contact us. Our phone number, web In addition, PagePal furnishes inputs CableAnalyzer TM All product names are trademarks of their respective companies. LIMITED Your charger is ETL listed to UL standards and meets all applicable FCC standards. WARNING: To reduce the risk of fire Follow all warnings and instructions marked on the product. Do not use this product near water - e.g., Printed in USA. All product names are trademarks of their respective companies. User s Manual All rights reserved. No part of this publication may be reproduced in any form or by any means or used to make any derivative Model RH520 OWNER S MANUAL Read these instructions before use.